Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 273

Страница: 273 / 548

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

273

Configure Switch Features

Chapter 7

Configure Traffic Permits and Fixups

Use caution when you configure traffic permits and fixups. We recommend
that you use the default values.

To configure traffic permits or fixups, follow these steps.

1. Click the Advanced tab.

2. Choose one of these options for incoming and outgoing packets that are

not handled by NAT:
• Pass-through—Permit the packets to pass across the NAT boundary.
• Blocked—Drop the packets.

3. In the Fix up Packets area, check or clear the checkboxes to enable or

disable fixups for ARP and ICMP.

By default, fixups are enabled for both ARP and ICMP.

4. Click Submit.

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ArmorStratix 5700 series

Отзывы:

Похожие инструкции для ArmorStratix 5700 series

Бренды по названию

Популярные бренды

Rockwell ArmorStratix 5700 series, Инструкция по эксплуатации

Результаты поиска

Содержание ArmorStratix 5700 series

Отзывы:

Похожие инструкции для ArmorStratix 5700 series

Бренды по названию

Популярные бренды