Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 548

background image

154

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 5

Install Stratix 5700 Switches

Connect to PoE Ports

Switches with PoE ports require a separate power supply. For power supply
requirements based on your application, refer to

.

1. Insert a straight-through, twisted four-pair, Category 5e or better cable

with an RJ45 connector into the PoE port.

2. Insert the other cable end into an RJ45 connector on the other PoE

powered device.

Connect to SFP Module Ports

To connect a fiber-optic cable to an SFP module, follow these steps.

1. Remove the rubber plugs from the module port and fiber-optic cable,

and store them for future use.

2. Insert one end of the fiber-optic cable into the SFP module port.

3. Insert the other cable end into a fiber-optic receptacle on a target device.

PoE In

put Pwr

48VDC, 1.2A

PoE Port

ATTENTION:

Do not remove the rubber plugs from the SFP module port or

the rubber caps from the fiber-optic cable until you are ready to connect the
cable. The plugs and caps protect the SFP module ports and cables from
contamination and ambient light.

LC Connector

«
...
152
153
154
155
156
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

xStack DGS-3612G series

Бренд: D-Link Страницы: 546

xStack DGS-3400 Series

Бренд: D-Link Страницы: 326

xStack DGS-3612G series

Бренд: D-Link Страницы: 493

xStack DGS-3400 Series

Бренд: D-Link Страницы: 540

DXS-3326GSR - xStack Switch - Stackable

Бренд: D-Link Страницы: 354

Бренд: Ubisys Страницы: 40

Baseline 2226 Plus

Бренд: 3Com Страницы: 4

Бренд: BABBITT Страницы: 14

Бренд: BABBITT Страницы: 10

Бренд: eao Страницы: 2

Бренд: eao Страницы: 2

Бренд: Fema Страницы: 96

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Бренд: Jabra Страницы: 4

Бренд: ORiNG Страницы: 2

Бренд: AVLT-Power Страницы: 12

SwitchMan USB-Combo SW2

Бренд: Raritan Страницы: 2

S6520X-EI Series

Бренд: H3C Страницы: 34

Бренд: C4i Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды