Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 364 | Manualshive

Страница: 364 / 548

background image

364

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 7

Configure Switch Features

Per Interface PortFast Table

Spanning tree requires an interface to progress through the listening and
learning states, to exchange information and establish a loop-free path before it
can forward frames. On ports that connect to devices such as workstations and
servers, you can allow an immediate connection. PortFast immediately
transitions the port into STP forwarding mode upon linkup.

To enable PortFast on an interface and apply the selected BPDU features to the
interface, select the interface, and then check Enable Port Fast.

Configure STP via the Logix Designer Application

STP configuration via the Logix Designer application is available for only
Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 switches.

In the navigation pane, click Switch Configuration.

In the Administration area, you can assign a Spanning Tree mode:

• Rapid Spanning Tree Protocol/Multiple Spanning Tree (RSTP/MST)
• Per VLAN Spanning Tree Plus (PVST+)
• Rapid Per-VLAN Spanning Tree (RPVST+)

MST/RSTP is the default.

Figure 49 - Switch Configuration for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches

«
...
362
363
364
365
366
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

Бренд: GHIELMETTI Страницы: 12

Бренд: LEGRAND Страницы: 30

Бренд: Eaton Страницы: 2

Бренд: Justin Страницы: 8

Бренд: PTN Страницы: 12

Бренд: Theben Страницы: 31

Бренд: VigilLink Страницы: 9

JetNet 5428G-20SFP Series

Бренд: Korenix Страницы: 2

Бренд: SEKURYX Страницы: 13

Бренд: Aaeon Страницы: 76

Essentials EXP-SW-0401-H2

Бренд: Wyrestorm Страницы: 2

Бренд: Clever Little Box Страницы: 12

AVS-OP-2404-210

Бренд: AMX Страницы: 1

BayStack 400-2FX

Бренд: Nortel Страницы: 8

Бренд: Icy Box Страницы: 8

Бренд: JABSCO Страницы: 2

Бренд: Ecler Страницы: 20

Бренд: Abtus Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды