Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 548

background image

74

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 3

Install Stratix 5400 Switches

ATTENTION: Prevent Electrostatic Discharge

This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these

guidelines when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

ATTENTION:

The console ports are intended for temporary local programming purposes only and not intended for permanent

connection.

The console port cables are not to exceed 3.0 m (9.84 ft) and must not contain hubs.

ATTENTION:

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment

may be impaired.

ATTENTION:

Before installing, configuring, operating, or maintaining this product, read this document and the documents

listed in the additional resources section for installing, configuring, or operating equipment. Users should familiarize themselves
with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

ATTENTION:

Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance shall be carried out by

suitably trained personnel in accordance with applicable code of practice. In case of malfunction or damage, no attempts at
repair should be made. The module should be returned to the manufacturer for repair. Do not dismantle the module.

ATTENTION:

This equipment is certified for use only within the surrounding air temperature range.

ATTENTION:

Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.

ATTENTION:

Electrical Safety Considerations

To comply with the CE Low Voltage Directive (LVD), all connections to this equipment must be powered from a source compliant

with the following:

• Safety Extra Low Voltage (SELV) Supply

• Protected Extra Low Voltage (PELV) Supply

«
...
72
73
74
75
76
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

DGS-1024D - Switch

Бренд: D-Link Страницы: 16

DGS-1016D - Switch

Бренд: D-Link Страницы: 44

DES-6000 Series

Бренд: D-Link Страницы: 3

DES-5024 - Switch

Бренд: D-Link Страницы: 2

DES-3828 - xStack Switch - Stackable

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 192

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 110

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 4

DGS-105 - Switch

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

Бренд: Accedian Страницы: 2

Бренд: Ubiquiti Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды