Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 548

background image

64

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 2

Get Started

Secure Digital (SD) Card

The following switches can store its configuration in an SD card or internal
memory:

• Stratix 5700 and ArmorStratix 5700 switches have a slot for an optional

SD card. You must use the 1784-SD1 card available from Rockwell
Automation with the switches.

• Stratix 5400 and Stratix 5410 switches ship with an SD card, which

stores the initial configuration and firmware for the switches.

You can use the SD card instead of internal memory to do the following:

• Restore a switch configuration in case of failure.
• Duplicate configurations when you are deploying a new network.
• Synchronize the initial configuration and firmware of a Stratix 5400

switch to internal memory.

In general, the start method for the switch becomes the source for any changes
you make to the configuration. For example, if you start from the SD card, any
changes you make are saved to the SD card. If you start the switch from internal
memory, even if you insert an SD card while starting the system, changes are
saved to internal memory.

You can use Device Manager or the Logix Designer application to synchronize
the SD card for configuration and IOS updates. The configuration
synchronization process synchronizes config.text and vlan.dat from the source
to the destination. If other files, such as back-up configurations, are present on
the SD card, they are not synchronized.

If you start the switch from the SD card and then remove it while the switch is
running, the following conditions apply:

• Device Manager is no longer be accessible.
• Changes that are made by using the CLI or the AOP take effect, but are

not saved when the switch is restarted.

• If you reinsert the SD card into the slot, changes are not saved to the card

unless new changes are made. Then the entire configuration is saved to
the card.

ATTENTION:

If a non-Rockwell SD card is used in Stratix switches, Rockwell

Automation reserves the right to withhold support.

ATTENTION:

When synchronizing, be aware of your start-up source, so that

you know which way to synchronize. Device Manager provides this
information on the Manual Sync tab. If you synchronize in the wrong
direction, you can overwrite your desired configuration.

«
...
62
63
64
65
66
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

Бренд: Gavita Страницы: 12

Бренд: Mach Power Страницы: 12

Бренд: E&C Страницы: 10

Бренд: N-Tron Страницы: 196

Бренд: N-Tron Страницы: 169

Бренд: Bridgetek Страницы: 2

Бренд: Allen-Bradley Страницы: 2

Бренд: Cumberland Страницы: 2

Бренд: Zektor Страницы: 41

Бренд: Unipoe Страницы: 9

Бренд: Cabletron Systems Страницы: 116

IES2016-16T Series

Бренд: 3onedata Страницы: 3

Бренд: Banner Страницы: 8

Бренд: GORMAN-RUPP PUMPS Страницы: 4

Бренд: AV Access Страницы: 16

Бренд: SALZ Страницы: 2

Бренд: Gigabyte Страницы: 2

Бренд: TRENDnet Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды