Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 548

background image

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

153

Install Stratix 5700 Switches

Chapter 5

Connect to 10BASE-T,
100BASE-TX, or 1000BASE-T
Ports

To connect to 10BASE-T, 100BASE-TX, or 1000BASE-T ports, follow these
steps.

1. Choose one of these options to connect a device:

• When connecting to workstations, servers, and routers, connect a

straight-through cable to an RJ45 connector on the front panel.

• When connecting to 1000BASE-T-compatible devices, use a twisted

four-pair, Category 5e or higher cable.

2. Connect the other end of the cable to an RJ45 connector on the other

device.

The Port status indicator turns on when both the switch and the
connected device have an established link.

The Port status indicator is amber while Spanning Tree Protocol (STP)
discovers the topology and searches for loops. This can take up to 30
seconds, and then the Port status indicator turns green.

The following conditions can prevent the Port status indicator from
turning On:
• The device at the other end is not turned On.
• A problem exists with a cable or the adapter that is installed in the

attached device.

3. Reconfigure and restart the connected device if necessary.

4. Repeat this procedure to connect each device.

ATTENTION:

To prevent electrostatic-discharge (ESD) damage, follow

recommended board and component handling procedures.

32291-M

10/100 Port

10/100/1000 Port

«
...
151
152
153
154
155
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

Бренд: Cabletron Systems Страницы: 88

Бренд: Eaton Страницы: 12

Бренд: socomec Страницы: 43

Бренд: Dahua Страницы: 15

Бренд: N-Tron Страницы: 169

Бренд: Guntermann & Drunck Страницы: 20

IPES-3424DSFP-2P

Бренд: Lantech Страницы: 26

Бренд: MLis Страницы: 85

Бренд: Epcom Страницы: 2

Lanolinx LNX-1002GN

Бренд: ANTAIRA Страницы: 110

5-Port Gigabit Switch 1000 Mbps

Бренд: Hama Страницы: 2

EXT-DVIK-MV-441

Бренд: Gefen Страницы: 136

GIGAswitch GSR-16

Бренд: Cabletron Systems Страницы: 346

Бренд: Danfoss Страницы: 2

Бренд: Tripp Lite Страницы: 17

Бренд: Raritan Страницы: 46

Elinx EIRP305-T

Бренд: B&B Electronics Страницы: 2

Бренд: Ross Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды