Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 352

Страница: 352 / 548

352

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 7

Configure Switch Features

Configure Smartports via Device Manager

From the Configure menu, choose Smartports.

Follow these guidelines when using Smartport roles:

• Before using Smartport roles, decide which switch port is connected to

which device type.

• Before attaching a device to the port or reconnecting devices that have

been moved, verify which Smartport role is applied to a port.

• If you attempt to apply a port role to a routed port in the Smartports

window, this error message appears:

A port role cannot be configured on a routed port.

To apply a Smartport role, follow this procedure.

1. From the Configure menu, choose Smartports.

2. Select a port.

3. From the pull-down menu in the Role column, choose a Smartport role.

4. Click Save.

IMPORTANT

We recommend that you do not change port settings after enabling

a Smartport role on a port. Any port setting changes can alter the
effectiveness of the Smartport role.

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ArmorStratix 5700 series

Отзывы:

Похожие инструкции для ArmorStratix 5700 series

Бренды по названию

Популярные бренды

Rockwell ArmorStratix 5700 series, Инструкция по эксплуатации

Результаты поиска

Содержание ArmorStratix 5700 series

Отзывы:

Похожие инструкции для ArmorStratix 5700 series

Бренды по названию

Популярные бренды