Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 376 | Manualshive

Страница: 376 / 548

background image

376

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 8

Monitor the Switch

Table 96 - Stratix 5700 and ArmorStratix 5700 Port Status Indicators

Mode

Status

Description

Status

In Status mode, the port status indicators show the connection and activity status of the port. Status mode is the default mode.

Off

No link present on the port.

Solid green

Port link; no activity.

Flashing green and off

Link is active and healthy.

Alternating green and
amber

There is a fault or error on the link.

Solid amber

The port is disabled.

Duplex

In Duplex mode, the port status indicators show the Duplex mode (Full-duplex or Half-duplex) of the ports. The 10/100/1000 ports operate only in Full-duplex
mode.

Off

The port is not operating.

Solid amber

The port is operating in Half-duplex mode.

Solid green

The port is operating in Full duplex mode.

Speed

In Speed mode, the port status indicators show the operating speed of the ports.

Off

The port is not operating.

Solid amber

The port is operating at 10 Mbps.

Solid green

The port is operating at 100 Mbps.

Flashing green

The port is operating at 1000 Mbps.

Power

In Power mode, the port status indicators show the status of PoE on switch models with PoE capability.

Off

PoE is disabled on the port.

Solid green

PoE is enabled on the port. The switch port is providing power.

Flashing green and
amber

PoE is denied because it exceeds the power capacity of the switch.

Flashing amber

PoE is denied because it exceeds the configured power limit for the switch port.

«
...
374
375
376
377
378
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

Бренд: B&B Electronics Страницы: 26

Бренд: B&B Electronics Страницы: 15

Бренд: B&B Electronics Страницы: 45

Бренд: Eaton Страницы: 8

Бренд: H3C Страницы: 38

Бренд: H3C Страницы: 36

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 36

S12500X-AF Series

Бренд: H3C Страницы: 21

S12500X-AF Series

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 16

Бренд: H-Tronic Страницы: 32

Бренд: Zektor Страницы: 65

Бренд: ATEN Страницы: 17

AW-FGT-100C-120

Бренд: Vivotek Страницы: 2

STI Echotel 919

Бренд: Magnetrol Страницы: 12

Бренд: Magnum Страницы: 3

Cyber SWITCH 1000

Бренд: Cabletron Systems Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды