Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 383

Страница: 383 / 548

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

383

Monitor the Switch

Chapter 8

Stratix 8000/8300 Front Panel

Table 101 - Stratix 8000/8300 System Status Indicators

Indicator

Status

Description

EIP Mod

The EIP Mod status indicator shows the status of the switch.

Off

Power to the switch is off or is not properly connected.

Solid green

The switch is operating properly.

Flashing green

The switch is not configured. For example, the switch does not have an IP address configured.

Flashing red

The switch has detected a recoverable system fault. Use the system log to see more details about the problem. See

System Log

Messages on page 392

Solid red

The switch has detected a nonrecoverable system. Use the system log to see more details about the problem. See

System Log

Messages on page 392

Flashing green and red

The switch is running its power-on self-test (POST).

EIP Net

The EIP Net status indicator shows the network status of the switch.

Off

Power to the switch is off or is not properly connected.

Solid green

The switch has an established CIP connection to one or more attached devices.

Flashing green

The switch has an IP address but the switch does not have an established connection to one or more attached devices.

Flashing red

One or more connections to attached devices have timed out.

Solid red

The switch has detected that its IP address is already in use by another device in the network.

Flashing green and red

The switch is running its power-on self-test (POST).

Setup

The configuration mode in which the switch is operating.

Off

The switch is configured as a managed switch or the switch is operating as an unmanaged switch.

Flashing green

Switch is in the initial Setup mode or is in the Direct Managed mode, or the initial setup is incomplete.

Pwr A and Pwr B The Pwr status indicators show the DC power status.

Off

Power to the switch is off or is not properly connected.

Solid green

Power is present.

Solid red

Power to the switch is not present and the power alarm is on.

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ArmorStratix 5700 series

Отзывы:

Похожие инструкции для ArmorStratix 5700 series

Бренды по названию

Популярные бренды

Rockwell ArmorStratix 5700 series, Инструкция по эксплуатации

Результаты поиска

Содержание ArmorStratix 5700 series

Отзывы:

Похожие инструкции для ArmorStratix 5700 series

Бренды по названию

Популярные бренды