RKI Instruments 72-0290-22 Скачать руководство пользователя страница 80

Страница: 80 / 163

80 • Start Up, Leak Check Mode

GX-2012 Operator’s Manual

6. If

CL RMNDR

is turned on (factory setting), the screen that appears next depends on

how

CL EXPRD

is set in the Maintenance Mode Menu (page 119).

•

If the unit is due for calibration and

CL EXPRD

is set to CONFIRM (factory

setting), then the following screen displays.

The alarm LED’s and buzzer will pulse several times. After this, press and

release the RESET SILENCE button to continue.

•

If the unit is due for calibration and

CL EXPRD

is set to NOT USE, then the

following screen displays.

The GX-2012 cannot be used until a calibration has been performed either by

selecting

AUTO CAL

, or

ONE CAL

in the Maintenance Mode menu. See

“Calibrating Using Auto Calibration” on page 97 or “Calibrating Using Single

Calibration” on page 100 for calibration instructions.

•

If calibration is not due or

CL EXPRD

is set to NO EFFECT, then the following

screen appears for a few seconds indicating when the next calibration is due.

   CAL

C--LIMIT

   FAIL

C--LIMIT

   2011
        9
     30
    69d

NEXT CAL

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды