RKI Instruments 72-0290-22 Скачать руководство пользователя страница 157

Страница: 157 / 163

GX-2012 Operator’s Manual

Bump Testing • 157

Bump Testing

NOTE:

The

BUMP DSP

menu item in Maintenance Mode is factory set to OFF. The

BUMP

menu item will not appear unless

BUMP DSP

is set to ON. See

“Turning the Bump Test Function On or Off” on page 115 for instructions.

NOTE:

The GX-2012 uses parameters defined in the

BUMP--SET

menu item of

Maintenance Mode while performing a bump test. To view or update these

parameters, see “Updating the Bump Test Parameters” on page 116.

NOTE:

If the combustible gas channel(s) are calibrated to a gas other than methane, use

an appropriate multigas cylinder.

From Measuring Mode, enter Calibration Mode by pressing and holding the (SHIFT)



button, then pressing the DISPLAY(ADJ) button and releasing both. If the unit prompts

you for the password, enter it by using the AIR



and (SHIFT)



buttons to select each

password number and then pressing and releasing POWER ENTER to confirm it and

move on to the next number. To go back a number, press and release the RESET

SILENCE button. The factory set password is the same as the factory set password for

Maintenance Mode: 2102. You can change the password by entering the

PASSWORD

menu item in Maintenance Mode. See “Turning the Password Function On or Off” on

page 128. If you enter an incorrect password, an error screen will display.

To return to normal operation, press and release the RESET SILENCE button. You may

then try to reenter Calibration Mode.
MAINTENANCE will appear along the top of the screen once you have entered

Calibration Mode. The first item in the calibration menu, AIR CAL, displays.
1. Slide the tubing clamp onto the tubing and connect the tubing onto the sample bag’s

inlet. Leave the clamp unclamped for now.

2. Connect the other end of the tubing to the regulator’s or dispensing valve’s hose barb

fitting.

3. Fill the gas collection bag by screwing the fixed flow regulator onto the calibration

cylinder or by screwing the dispensing valve onto the calibration cylinder and turning

the knob counterclockwise.

NOTE:

If the regulator has no on/off knob, then gas will begin to flow at 0.5 LPM as

soon as the regulator is connected to the cylinder.

4. Allow the gas to dispense until the gas collection bag is a little over half full.

Err

PASSWORD

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды