RKI Instruments 72-0290-22 Скачать руководство пользователя страница 107

Страница: 107 / 163

GX-2012 Operator’s Manual

Using Maintenance Mode • 107

•

To return to the main menu, press POWER ENTER at any time. If any channel

failed the calibration, the buzzer will sound a double pulsing tone until you press

and release the POWER ENTER button.

•

Disconnect the tubing from the probe.

13. Unscrew the demand flow regulator from the calibration cylinder.
14. With the

BUMP

menu option displayed, press the (SHIFT)



button until the

NORMAL

menu option is displayed.

15. Press and release the POWER ENTER button to return to Measuring Mode.

Turning the Lunch Break Setting On or Off

With

LNCH BRK

set to

OFF

(factory setting), the GX-2012 automatically starts new

TWA and PEAK reading collection and resets the time in operation at startup.
With

LNCH BRK

set to

, the Resume Measurements Screen displays during startup.

From this screen, you can choose to continue accumulating TWA and PEAK readings and

the time in operation from the last time the GX-2012 was used or start collecting new

readings and reset the time in operation.
1. Use the AIR



or (SHIFT)



buttons to display the

LNCH BRK

menu item.

       49
  12.0
         5
  25.0

%LEL

ppm

MAINTENANCE

/CAL

MAINTENANCE

BUMP

MAINTENANCE

LNCH BRK

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды