RKI Instruments 72-0290-22 Скачать руководство пользователя страница 138

Страница: 138 / 163

138 • Replacing or Recharging the Batteries

GX-2012 Operator’s Manual

Figure 23: Putting the GX-2012 into the Charging Station

5. When a full charge has been reached, approximately 4 hours, the red LED on the

charging station will turn off. Remove the GX-2012 from the charging station and

unplug the charging station’s power cord from the AC outlet.

Recharging the Lithium Ion Battery Pack Out of the Instrument

The lithium ion battery pack may be charged using the charging station while it is out of

the GX-2012. This is useful if spare battery packs are kept in case the pack in the GX-

2012 needs to be charged, but the unit must be used immediately. In this case, a spare

charged pack can be installed in the GX-2012 and the dead pack charged in the charging

station.
1. Make sure the GX-2012 is off.
2. Confirm that the adapter’s DC output cord is plugged into the charger. If a multi-

instrument charging station is being used, the same AC adapter is used as for the

single instrument charging station.

Red Charging LED

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды