RKI Instruments 72-0290-22 Скачать руководство пользователя страница 28

Страница: 28 / 163

28 • Start Up, Normal Mode

GX-2012 Operator’s Manual

11. If the GX-2012 experiences a sensor failure during start up, a screen indicating which

sensor failed displays. In the example below, the CO sensor has failed.

If you wish to continue, press and release the RESET SILENCE button to

acknowledge the failure. The gas reading for the failed sensor will be replaced by

“---”. Replace the failed sensor as soon as possible.

12. The GX-2012 is now operating in Normal Mode and monitoring for gas in Measuring

Mode. The Normal Operation Screen appears.

The concentrations of the target gases are displayed along with the time and battery charge

level. The heart symbol displayed just to the left of the battery charge level flashes while

the instrument is functioning properly. If it disappears or is steadily on, the unit is

experiencing a microprocessor error. The fan symbol just to the left of the heart symbol

spins while the pump is operating.

Turning On the GX-2012 in Normal Mode With All Modes Active

If the

L./B. MODE

item in Maintenance Mode is set to LC, bH, or LC bH (see “Updating

the Leak Check/Bar Hole Mode Setting” on page 125), then the user must select Normal

Mode during the start up sequence to operate in Normal Mode. The standard factory

setting for

L./B. MODE

is OFF. See “Chapter 4: Using the GX-2012 in Bar Hole Mode”

on page 69 for a description of Bar Hole Mode or “Chapter 5: Using the GX-2012 in Leak

Check Mode” on page 78 for a description of Leak Check Mode.
The following description of the GX-2012 start up sequence assumes that the following

menu items in Maintenance Mode are turned on:

LNCH BRK

ID DISP

CL RMNDR

and

BP RMNDR

. If any of these items is turned off, then the corresponding screen will

not appear. It also assumes that the

L./B. MODE

menu item in Maintenance Mode is set

to LC bH. If

L./B. MODE

is set to LC, the Bar Hole Mode Select Screen will not appear.

L./B. MODE

is set to bH, the Leak Check Mode Select Screen will not appear.

1. Connect the tapered rubber nozzle or the sample hose to the GX-2012’s quick connect

inlet fitting.

2. If a sample hose is used, screw the probe onto the sample hose’s threaded fitting.

FAIL

ppm

SENSOR

        0
   20.9
     0
   0.0

%LEL

ppm

22:37

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды