RKI Instruments 72-0290-22 Скачать руководство пользователя страница 122

Страница: 122 / 163

122 • Using Maintenance Mode

GX-2012 Operator’s Manual

1. Use the AIR



or (SHIFT)



buttons to display the

BP EXPRD

menu item. Press

and release the POWER ENTER button. The screen will indicate the current setting.

2. Use the AIR



or (SHIFT)



button to display the desired setting along the bottom of

the screen.

3. Press and release the POWER ENTER button to save the setting and return to the

main menu.

Updating the Bump Test Check Setting

This item setting defines which sensors are used to update the bump test reminder screen.

B--CHECK

can be set to 4-GAS or ALL. If

B--CHECK

is set to 4-GAS (factory setting),

the calibration dates for only the standard 4 sensors (LEL, O

, H

S, and CO) are used to

determine if a bump test is due. If

B--CHECK

is set to ALL, the calibration dates for the

standard 4 sensors along with the %volume sensor are used to determine if a bump test is

due.
1. Use the AIR



or (SHIFT)



buttons to display the

B--CHECK

menu item. Press

and release the POWER ENTER button. The screen will indicate the current setting.

2. Use the AIR



or (SHIFT)



button to display the desired setting.

3. Press and release the POWER ENTER button to save the setting and return to the

main menu.

   tESt

SEL

MAINTENANCE

CONFIRM

4GAS

MAINTENANCE

B--CHECK

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды