RKI Instruments 72-0290-22 Скачать руководство пользователя страница 112

Страница: 112 / 163

112 • Using Maintenance Mode

GX-2012 Operator’s Manual

7. Press POWER ENTER to save the setting. The unit will direct you back to the Alarm

Points Screen where you can use the AIR



or (SHIFT)



buttons to select the

oxygen channel.

Press POWER ENTER.

8. The first selection for the oxygen channel is the alarm pattern.

The choices are L-H, L-LL, or H-HH. The L-H pattern provides a decreasing warning

and an increasing alarm. The L-LL pattern provides a decreasing warning and a

decreasing alarm. The H-HH pattern provides an increasing warning and an

increasing alarm. This setting is for operation in inert atmospheres and will cause

INERT to appear along the bottom line of the display during Normal Operation. Make

your selection using the AIR



or (SHIFT)



buttons and press POWER ENTER

when finished. The factory setting is L-H.

9. You may then adjust the warning setting and alarm setting for the oxygen channel

using the AIR



or (SHIFT)



buttons. Press POWER ENTER when finished with

each selection to return to the Alarm Points Screen.

10. Use the AIR



or (SHIFT)



buttons to select the CO channel and press POWER

ENTER to display the warning setting.

11. Adjust the values for the warning and alarm settings using the procedure in step 4

through step 7. When you press POWER ENTER after selecting the alarm value, you

will then be prompted to select the STEL value.

    - - -

MAINTENANCE

ALARM--P

  L-H

MAINTENANCE

ALM PTN

200

ppm

MAINTENANCE

STEL

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды