RKI Instruments 72-0290-22 Скачать руководство пользователя страница 67

Страница: 67 / 163

GX-2012 Operator’s Manual

Calibration Mode • 67

If any channel fails the bump test,

•

The instrument will beep and a calibration is immediately and automatically

started. Continue to apply the calibration gas. CAL on the bottom left of the

screen will alternate with APPLY.
The calibration time will begin to countdown in seconds in the lower right of the

screen. The calibration time counted down during a calibration initiated because

of a failed bump test is the difference between the bump test gas time and the

calibration time defined in the

BUMP--SET

menu item in Maintenance Mode.

•

At the end of the calibration, the instrument displays the results from both the

bump test and the calibration. Use the AIR



or (SHIFT)



button to scroll

between the calibration/bump test results, the bump test gas readings, and the

calibration gas readings.

         1
  20.9
     37
  10.0

%LEL

ppm

MAINTENANCE

CAL 60

  FP
  PP
  FF
    PP

%LEL

ppm

MAINTENANCE

BUMP/CAL

         1
  12.0
         5
    23.0

%LEL

ppm

MAINTENANCE

BUMP/

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды