RKI Instruments 72-0290-22 Скачать руководство пользователя страница 25

Страница: 25 / 163

GX-2012 Operator’s Manual

Start Up, Normal Mode • 25

6. If

BP RMNDR

is turned on (factory setting is OFF), the screen that appears next

depends on how

BP EXPRD

is set in the Maintenance Mode Menu (page 119).

•

If the unit is due for a bump test and

BP EXPRD

is set to CONFIRM (factory

setting), then the following screen displays.

The alarm LED’s and buzzer will pulse several times. After this, press the

RESET SILENCE button until you hear a beep to continue.

•

If the unit is due for a bump test and

BP EXPRD

is set to NOT USE, then the

following screen displays.

The GX-2012 cannot be used until a bump test has been performed by selecting

BUMP

in the Maintenance Mode menu. See “Performing a Bump Test” on

page 102 for bump testing instructions.

•

If a bump test is not due or

BP EXPRD

is set to NO EFFECT, then the following

screen appears for a few seconds indicating when the next bump test is due.

NOTE:

If both

CL RMNDR

and

BP RMNDR

are turned off, a WARM UP screen will

display before the warm up sequence continues.

tESt

B--LIMIT

   FAIL

B--LIMIT

   2011
        9
      30
   10d

NEXTBUMP

www.calcert.com

[email protected]

1.800.544.2843

Содержание 72-0290-22




































































































































































Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды

RKI Instruments 72-0290-22, Руководство оператора

Результаты поиска

Содержание 72-0290-22

Отзывы:

Похожие инструкции для 72-0290-22

Бренды по названию

Популярные бренды