quid contacts eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or
ambient temperatures of
5°C/40°F or
b
40°C/105°F.
g) Do not dispose defective batteries in the normal domestic waste.
Take them to an authorised REMS after-sales service facility or to a
reputed waste disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
b) Comply with maintenance instructions and instructions on tool re-
placements.
c) Check mains lead of power tool regularly and have it replaced by a
qualified expert or an authorised REMS after-sales service facility in
case of damage. Check extension cable regularly and replace it when
damaged.
Specific Safety Instructions
•
The machine is operated with a safety-type, jog control pedal switch
with emergency-off function. If the danger area constituted by the rota-
ting workpiece is not clearly visible from where the operator is located,
safety precautions, e.g. barriers, must be used.
•
Do not undertake any operations such as hemping, installation and re-
moval, thread cutting with manual die stocks, working with pipe cutters
or holding the workpiece manually (instead of using the material sup-
ports) when the machine is operating.
•
If there is a risk of the workpiece bending and whipping round (this de-
pends on the length and cross-section of the material and on the speed)
or at insufficient stability of the machine a sufficient number of height-
adjustable supports (REMS Herkules) must be used.
•
Never reach into the chuck.
•
Clamp short pieces of pipe only with the REMS Nippelspanner or the
REMS Nippelfix.
•
REMS thread-cutting oils in spray cans (REMS Spezial, REMS Sanitol)
are environment-friendly but contain combustible propellant (butane).
Spray cans are pressurized – do not force open. Also, protect them from
exposure to strong sunlight and heating above 50°C.
•
Due to the degreasing effect of the cooling lubricants (thread-cutting
oils), an intensive skin contact has to be avoided. An appropriate skin
protector has to be applied.
•
Due to hygienical reasons the trough has to be cleaned regularly from
dirt and chips, at least, however, once a year.
•
It is not required to check the cooling lubricant because, due to the con-
sumption, new cooling lubricant is refilled from time to time.
•
Do not allow undiluted cooling lubricant to get into drainage, water sy-
stems or the soil. Remaining cooling lubricants have to be delivered to
specialized waste disposal companies. Disposal identity number for mi-
neral-based cooling lubricants 54401, for synthetic 54109.
eng
eng
1. Technical data
Tornado 2000
Magnum 2000
Magnum 2000
Tornado 2000
Magnum 4000
Tornado 2010
Magnum 2010
Magnum 2010
Tornado 2010
Magnum 4010
Tornado 2020
Magnum 2020
Magnum 2020
Tornado 2020
Magnum 4020
with REMS 4”
with REMS 4”
Automatic die head
Automatic die head
1.1. Capacity
1.1.1. Thread diameter
Pipe (including plastic coated)
1
/
16
– 2”
1
/
16
– 2”
1
/
16
– 4”
1
/
16
– 4”
1
/
4
– 4”
Bolt
6 – 60 mm
6 – 60 mm
6 – 60 mm
6 – 60 mm
14 – 60 mm
1
/
4
– 2”
1
/
2
– 2”
1
/
4
– 2”
1
/
4
– 2”
1
/
2
– 2”
1.1.2. Types of threads
Pipe threads, tapered
R (ISO 7-1, DIN 2999, BSPT), NPT
Pipe threads, parallel
G (ISO 228-1, DIN 259, BSPP), NPSM
Threads for conduits
Pg (DIN 40430), IEC
Bolt threads
M (ISO 261, DIN 13), UNC, BSW
1.1.3. Thread length
Pipe threads tapered
standard length
standard length
standard length
standard length
standard length
165 mm (6.5”),
150 mm (6”),
165 mm (6.5”),
165 mm (6.5”),
150 mm (6”),
Pipe threads parallel
unlimited by
unlimited by
unlimited by
unlimited by
unlimited by
Bolt threads
}
repeated clamping
repeated clamping
repeated clamping
repeated clamping
repeated clamping
1.1.4. Cutting
Pipe
1
/
8
– 2”
1
/
8
– 2”
1
/
8
– 2”
1
/
8
– 2”
1
/
4
– 4”
1.1.5. Internal deburring
Pipe
1
/
4
– 2”
1
/
4
– 2”
1
/
4
– 2”
1
/
4
– 2”
1
/
4
– 4”
1.1.6. Nipples and double nipples
with REMS Nippelspanner
(internal clamping)
3
/
8
– 2”
3
/
8
– 2”
3
/
8
– 2”
3
/
8
– 2”
3
/
8
– 2”
with REMS Nippelfix
(automatic internal clamping)
1
/
2
– 4”
1
/
2
– 4”
1
/
2
– 4”
1
/
2
– 4”
1
/
2
– 4”
1.1.7. REMS 4”Automatic die head
for all types Tornado and Magnum
2000/2010/2020 (see Fig. 6)
2
1
/
2
– 4”
2
1
/
2
– 4”
1.2.
Spindle speed
Tornado 2000
1
/
16
– 2”
53 – 40 rpm
Magnum 2000
1
/
4
– 2”
53 – 40 rpm
Magnum 4000
1
/
4
– 4”
23 – 20 rpm
automatic infinitely variable speed
Tornado 2010 / 2020
1
/
16
– 2”
52
1
/min
Magnum 2010 / 2020
1
/
4
– 2”
52 – 26 rpm
Magnum 4010 / 4020
1
/
4
– 4”
20 – 10 rpm
also under full load. On heavy duty and weak voltage for larger threads Tornado 26 rpm resp. Magnum 10 rpm.
