Quantum ActiveScale X100, Руководство по установке, Страница: 187 / 265

ActiveScale™ OS X100 Rackless Installation Guide
187
c. Run the following commands:
(SiteN_System_Interconnect1) >en
(SiteN_System_Interconnect1) #conf
(SiteN_System_Interconnect1) (Config)#interface 0/49
(SiteN_System_Interconnect1) (Interface 0/49)#no shutdown
(SiteN_System_Interconnect1) (Interface 0/49)#exit
(SiteN_System_Interconnect1) (Config)#interface 0/51
(SiteN_System_Interconnect1) (Interface 0/51)#no shutdown
(SiteN_System_Interconnect1) (Interface 0/51)#exit
(SiteN_System_Interconnect1) (Config)#exit
(SiteN_System_Interconnect1) #write memory confirm
Config file 'startup-config' created successfully. Configuration Saved!
(SiteN_System_Interconnect1) (Config)#show interfaces status all | include 0/49
0/49ScaleoutNetwork_InterconnectUp40G Full40G FullUnknown Active
(Site1_Storage_Interconnect1) (Config)#show interfaces status all | include 0/51
0/51ScaleoutNetwork_InterconnectUp40G FullUnknown Inactive
(SiteN_System_Interconnect1) (Config)#exit
2. Create an alias on your laptop to System Interconnect 2 on the existing system:
Note: Change the IP address in the first alias to match your network settings, but
do not change the link-local IP address in the second alias.
sudo ifconfig eth1:0 172.16.210.240 up #this IP address should match your setup
sudo ifconfig eth1:1 169.254.210.240 up
3. Connect to
System Interconnect 2
(username:
admin
, no password):
lab@mw-<System IP>:$ telnet <IP of System Interconnect 2> Trying 172.16.210.200...
Connected to 172.16.210.200. Escape character is '^]'. User:admin
Password:
4. Run the following commands:
(SiteN_System_Interconnect2) >en
(SiteN_System_Interconnect2) #conf
(SiteN_System_Interconnect2) (Config)#interface 0/49
(SiteN_System_Interconnect2) (Interface 0/49)#no shutdown
(SiteN_System_Interconnect2) (Interface 0/49)#exit
(SiteN_System_Interconnect2) (Config)#interface 0/51
(SiteN_System_Interconnect2) (Interface 0/51)#no shutdown
(SiteN_System_Interconnect2) (Interface 0/51)#exit
(SiteN_System_Interconnect2) (Config)#exit
(SiteN_System_Interconnect2) #write memory confirm
Config file 'startup-config' created successfully. Configuration Saved!
(SiteN_System_Interconnect2) #show interfaces status all | include 0/49
0/49ScaleoutNetwork_InterconnectUp40G Full40G FullUnknown Active
(SiteN_System_Interconnect2) #show interfaces status all | include 0/51
0/51ScaleoutNetwork_InterconnectUp40G FullUnknown Inactive
(SiteN_System_Interconnect2) #quit
Connection closed by foreign host.
5. Reconfigure the System Interconnects on the new systems:
a. Connect an Ethernet cable from your laptop to port 44 on System Interconnect 1 of the new system.
b. Create an alias on your laptop to
System Interconnect 1
on the new system:
Note: Do not change the link-local IP address in the command below.
sudo ifconfig eth1:0 <ip_address> up
c. Connect to
System Interconnect 1
(username:
admin
, no password):
lab@mw-<System IP>:~$ telnet <System Interconnect 1 IP> Trying