PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 98

Страница: 98 / 176

4-4

VIBXPER

T II 05.2012

Time waveform

The measurement results are displayed as an XY diagram in the top

section of the window (see the standard setting). The data field in the

lower half lists the two highest amplitudes (positive & negative). If a

threshold value is exceeded, the absolute value and the difference to

the measurement value is displayed ('delta', see below).
The following functions are available for evaluation of the result:

Zoom the time (X) axis

• Press the '+' key to magnify the X axis. Depending on the zoom

mode (page 4-18), the main cursor is used as the central point or

the gap between the main and delta cursor is magnified. The '–' key

is used to zoom out.

Scaling the amplitude (Y axis)

• Press the navigation key up to magnify the scaling of the Y axis and

to make low amplitudes visible.

• To reduce the scaling again, press the navigation key down.

Rotational speed marker

The yellow rotational speed markers indicate the trigger pulses dur-

ing signal measurement. In the circular plot, the speed markers also

indicate the direction of rotation (see the next page).

Cursor

The cursor coordinates are displayed above the diagram.
• Press the MENU key and click on 'Cursor'.

one

: Hide all cursors (Zoom / scaling not possible!)

ain

: Show main cursor

Press the navigation keys right/left to move the cursor. The speed

increases if you keep the navigation key pressed.

Results

Result screen of a

time waveform measurement

Zoomed area

Cursor coordinates

Threshold

Speed marker

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды