PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 102

Страница: 102 / 176

4-8

VIBXPER

T II 05.2012

Spectrum, Cepstrum

The measurement result is displayed in the upper pane. The measured

time waveform is displayed in the lower pane during the measure-

ment. After the measurement, the following information can be dis-

played:
- Max 10 (10 highest amplitudes in the spectrum)

- Alarms

- Frequency marker (only in Route / Template mode)

- Trending values (only in TrendingSpectrum)

- Trending bars (only in TrendingSpectrum)

- Time waveform measured

- Position of the main cursor

• Press the MENU key and select the 'Info' option.

• Click on the desired piece of information:

The data to be displayed by default after the measurement is set in

the display setup (see p. 4-18).
The active window pane is highlighted by a frame. Press the F key

to switch to the other window pane.

Info / Max 10

Lists the 10 highest amplitudes in the spectrum. Click on an entry

to set the cursor to the corresponding line of the spectrum. You can

sort the list for amplitude or frequency in ascending or descending

sequence. To do so, click on the respective column title.

Results



Note

Left:

Spectrum & time waveform

Right:

Additional information

In-depth information is given in the sec-
tion 'Measurement Tasks' (Ch. 5).

Amplitude, Envelope, Order

Upper window pane is active

Trending, Trending envelope, Cepstrum

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды