PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 88

Страница: 88 / 176

3-38

VIBXPER

T II 05.2012

Recording

Testing the rpm sensor

To test the function and the positioning of the rpm sensor, a test mea-

surement can be performed prior to the measurement recording:
• Press the MENU key and click on ‘Test speed’.

• To return to the configuration screen after the test measurement,

press the ESC button.

Displaying the characteristic overall values

During the measurement recording, a dialog window appears in the

measurement screen with an overview of the configuration settings.

Optionally, you can also display an Overall value overview (see be-

low):
• Press the MENU key in the configuration screen and click on ‘Over-

all overview’ (see below).

• Activate the overall values to be displayed, and select, if necessary,

an additional parameter (maximum, minimum, max./min.). Up to

nine values can be displayed at the same time.

To hide the dialog window and display the concealed areas of the

measurement screen, press the F key.

Starting the measurement recording

• Press the MENU key in the configuration screen and click on ‘Start’.

The measurement screen appears. A dialog is displayed in the fore-

ground that contains the most important information on the record-

ing: start conditions, stop conditions, trigger variable (time or rpm),

number of measurement values already recorded (see below).
A sensor test is always performed prior to recording. Exception: the

start condition is set to 'Immediately'.

Left:

Measurement value recording

Display of the recording configuration

and overall value overview (optional)

Right:

Overall value overview

Configuration

Maximum number of values: 9

(here: 8 values are displayed)

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды