PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 91

Страница: 91 / 176

3-41

VIBXPER

T II 05.2012

Multiplexer

Data acquisition at the VIBRONET multiplexer

For automatic data acquisition at many measurement locations of the

same type or hard-to-access measurement locations, VIBXPERT and

OMNITREND feature the function ‘Multiplexer measurement’. The

respective measurement tasks are processed within a route or as a

machine template.
The measurement locations are combined by the VIBRONET field

multiplexer (VIB 8.306) on one string line and are measured consecu-

tively.

Only vibration measurements with Current Linedrive accelerom-

eters are possible.
Up to 6 multiplexers with a maximum of 54 measurement locations

are possible on one string line.
To connect VIBXPERT to a multiplexer you need the following:

• Connecting cable, VIB 5.346

• BNC connecting adapter, VIB 5.346 MUX
For RPM-dependent measurements (e.g. phase), you have to install

the sensor (VIB 6.631) at a suitable measurement location. RPM

measurements via multiplexers are not possible.

VIB 5.346 MUX

VIB 5.346



Note

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды