PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 23

Страница: 23 / 176

2-11

VIBXPER

T II 05.2012

Getting started - Memory card

Notch for silicone adhesive (framed)

• Coat the groove along the edge of the card compartment cover

with a small amount of silicone adhesive (NOVASIL S-11) and re-

place the cover. Remove any excess adhesive with a cloth.

The cover can also be replaced without silicone adhesive. The de-

vice complies with protection class IP 55 then.

When the device is switched on, the card is automatically tested. The

following scenarios are possible:

Card formatted, which version?

- The card is new and has not yet been formatted in a VIBXPERT:

you are prompted to format the card.

- The card has already been used in another VIBXPERT:

Card version < firmware version in the device: the files on the card

are automatically updated.

Card version > firmware version in the device: you are prompted

to reset all settings to the "factory settings" ('Reset', P. 2-29).

Card version = latest firmware version: no action.

Card faulty?

- The file system on the card is damaged. A warning appears along

with the instruction to have the card repaired. If possible, make a

backup copy of the measurement data (see 'Backup', page 6-8).

Start card formatting and repair in the 'Service' menu (P. 2-29).

How much free memory capacity is there?

The free memory capacity is checked regularly during operation. A

message appears when the memory is almost full.



Note

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды