PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 83

Страница: 83 / 176

3-33

VIBXPER

T II 05.2012

Near location

Restrictions

- The grouping of measurement tasks to a 1+1 measurement is only

possible if firmware module ‘2 channels’ (VIB 5.381) has been reg-

istered in the device.

- For ‘Near locations’, the "Multitask" measurement task is disabled.

- In the route runtime setup, a standard sensor should not be set up

and the measurement channel must be set to 'Auto' (p. 3-18).

- Because a trend display is not possible for 1+1 measurements, the

last measured result always appears when a result is loaded via the

measurement task selection.

Options during the route

Skipping a measurement location/measurement task (see p. 3-10):

- If you skip over a measurement task, only the grouped measure-

ment task within the 1+1 measurement is skipped.

- If you skip a measurement location, the near location is skipped as

well - including all associated measurement tasks.

Disabling the spatial sequence:

‘Near location’ can be disabled in the route:

This procedure affects the selected route element and the appropri-

ate tasks. This procedure cannot be reversed!

• In the tree/list view, select a route element and press the MENU

key.

• Click on ‘Break near location’ (see below).

All lower level measurement tasks are then performed like nor-

mally configured one-channel measurements.

Attention!

Disabling near location(s)

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды