PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 146

Страница: 146 / 176

5-26

VIBXPER

T II 05.2012

Left:

Reference measurement

is required when measuring on a run-

ning machine

Right:

Dataset selection

Single measurements /

Averaged final result

Measurement tasks

Tips for setting the measurement parameters

Set the 'Trigger Start" time to a negative value in order to record the

signal before the excitation.
If the measurement starts before the excitation, increase the trig-

ger threshold in the measurement setup by approximately half (P.

3-22).
If the response signal overloads, increase the 'Measurement Range'

parameter in the measurement setup accordingly (P. 3-22).



Note

Measurement with the machine running

• Enable 'Negative averaging' in the measurement setup.

• Perform the individual impact tests.

• Click on 'Start' in the window that opens to measure the reference

spectrum - without producing a machine excitation!

• Click on 'Stop' when a sufficient number of reference spectra have

been recorded and averaged to form a result (see below).

Displaying the results

• Activate the upper pane with the F key (Spectrum, P. 4-8).

• Press the MENU key and click on 'Choose Dataset'.

The results of the impact test, the average final result and the refer-

ence measurement (negative averaging) are listed here and can be

displayed individually by clicking (see below).

• To close the list, press on the ESC key.

Repeating individual measurements

• Activate the upper pane using the F key.

• Press the MENU key and click on 'Repeat'.

• Click on the respective measurement in the list.

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды