PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 53

Страница: 53 / 176

3-3

VIBXPER

T II 05.2012

Measurement - Multimode

Multimode: Measurement, Analysis, Diagnosis

To activate the 'Multimode' mode, click on the corresponding symbol

in the start screen. The measurement tasks appear in the selection

screen (see below). The measurement task for the selected icon is

displayed below the icon field.
The measurement tasks are grouped into three tabs: Overall (charac-

teristic) Values, Signals, Advanced (measurements). Certain measure-

ment tasks only appear if the corresponding module is registered.
The current tab sheet is highlighted with a black frame. To change

the tab sheet, press the '+/-' key or highlight the tab sheet with the

navigation keys.

Typical workflow of a measurement

This section shows you how to carry out a measurement in multimode

mode if the preparations have already been made. A schematic of the

workflow of a measurement is shown below.
The setting options that are available before, during and after a mea-

surement are described in the following section. The evaluation of the

results on the instrument* is described in Chapter 4.

Starting a measurement:

• Highlight the measurement icon in the selection screen.

• Connect the sensor.

Sensor and measurement channel are displayed in the info field.

Standard sensor is active when the sensor icon at the top left is or-

ange and the sensor type in the info field is marked red! The sensor

setup is overwritten with the standard sensor.

• Press 'Enter' to start the measurement.

* Multimode measurements can also be
imported and evaluated in OMNITREND.

Select
operating mode

Select task, start
measurement

Save result

Multimode selection screen

for overall value measurements

Measurement quantity

(icon)

Measurement task

Info field

Sensor type:
VIB 6.142 (here: default sensor)

Tab

Attention!

Default vibration sensor enabled

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды