PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 65

Страница: 65 / 176

3-15

VIBXPER

T II 05.2012

Start measurement

• Click on 'Machine template' in the start screen.

A list of the available machine templates appears (see below).

Machines where measurements have already been carried out ap-

pear subordinate to the associated template. The number of the

measured measurement location and the total number of measure-

ment locations is indicated in the right column ('Finished') for each

machine.

The info field for the highlighted machine at the bottom shows

when the corresponding template was loaded into the data collec-

tor and when the last measurement was carried out.

To continue the measurement on a machine, click on the corre-

sponding subordinate machine.

• Click on the template that you want to use for the measurement.

The ‘Machine description’ dialog appears where a name for the

new machine is specified.

• If you do not want to enter any further information, press the

MENU key and click on ‘OK’ to accept the name.

• Otherwise press the MENU key, click on ‘Details’ (see below) and,

if necessary, enter the necessary data as follows:

- Position the cursor in the corresponding text field and press 'Enter'

to open the text editor.

- After entering the data, press the MENU key and click on OK.

You can change the machine description at any time.

Left:

Enter machine details

Right:

Machine template list

Template

Machine

Measurement - Machine template



Note

Info field

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды