PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 31

Страница: 31 / 176

2-19

VIBXPER

T II 05.2012

Getting started - Basic settings

Transducers

The transducer menu (see below) contains all of the functions and pre

settings for the transducer. Click on 'Transducers' to open the menu.

Available transducers in VIBXPERT

The measurement-relevant parameters for many transducers are

stored in VIBXPERT. Consequently, when putting together a measure-

ment task, it is only necessary to select the transducer required for the

measurement.
The transducer list (see below) in the 'Available transducer' menu

contains all the factory-configured and user-defined transducers. Un-

der certain circumstances, this list can be very extensive.

Preselecting available transducers

As it is probable that not all the transducers stored in VIBXPERT

will be used, the choice can be restricted to those transducers that

are available to the user. When setting up the measurement tasks,

VIBXPERT only offers the choice of the preselected transducers as

standard:
• Click on each of the relevant transducers in the list so that these are

marked with a cross.

Displaying the transducer application

To check in which measurement task(s) the individual transducers are

used, proceed as follows:
• Mark the relevant transducer in the list.

• Press the MENU key.

• Click on 'Usage' (see below).
A list appears to show the measurement tasks that are measured with

the transducer.

Left:

Transducer menu

Right:

Available transducers

are marked with

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды