Powis Parker Fastback 8x Скачать руководство пользователя страница 44

Страница: 44 / 83

Page 40 FB8X Service Manual Rev. C, 9/28/10

S E R V I C E M E N U

5 . 4 T E S T I N G A N D C A L I B R A T I O N

5.4.6 Checking the Resistance of the Heater Sensors

1. Turn off the machine. Make sure the machine is

unplugged.

2. Remove the Front Cover.
3. Disconnect the Heater Sensor connections

(J1/J2/J3).

4. Touch the red and black probes to each connector

as shown.

5. Verify all Heater sensor connectors have a reading

of 120 ohm +/- 15% at 20°C/68°F.

(J1) Spine Heater Connector

(J3) Back Heater Connector

(J2) Bender Heater Connector

6. Attach a ground connector to the chassis of the machine as shown.

Touch the red probe to each sensor connector. Each heater should
have a reading greater than 100,000 ohm. Reconnect the heaters.

Ground Connector

TOOLS REQUIRED: #1 Phillips Screwdriver, Ohmmeter

Содержание Fastback 8x




















































































Результаты поиска

Содержание Fastback 8x

Отзывы:

Powis Parker Fastback 8x, Руководство по обслуживанию, Страница: 44 / 83

Результаты поиска

Содержание Fastback 8x

Отзывы: