Powis Parker Fastback 8x Скачать руководство пользователя страница 33

Страница: 33 / 83

FB8X Service Manual Rev. C, 9/28/10 Page 29

S E R V I C E M E N U

5.3.4 INFO

SHOW COUNTS

This menu displays two alternating values for the number of binds the machine has performed and the number of

cycles. Binding a book counts for 1 bind + 1 cycle. Running an autocycle in either Standard or Fast mode, counts

for only 1 cycle.

SHOW VERSION

This menu displays the version of firmware installed in the binder.

5.3.5 HEATERS

HEATER TEST

TEST ALL

Selecting this menu will allow you to turn on and test all three heaters at the same time. Press the BIND

button to turn the heaters on and off. During the heater test, internal diagnostic values will appear on the

display. The diagnostic values are for use by Powis Parker technicians only.

TEST SPINE

Selecting this menu will allow you to turn on the Spine Heater only. Press the BIND button to turn the

heater on and off. During the heater test, internal diagnostic values will appear on the display.

The diagnostic values are for use by Powis Parker technicians only.

TEST BENDER

Selecting this menu will allow you to turn on the Bender Heater only. Press the BIND button to turn the

heater on and off. During the heater test, internal diagnostic values will appear on the display.

The diagnostic values are for use by Powis Parker technicians only.

TEST BACK

Selecting this menu will allow you to turn on the Back Heater only. Press the BIND button to turn the

heater on and off. During the heater test, internal diagnostic values will appear on the display.

The diagnostic values are for use by Powis Parker technicians only.

SET FAN

This menu sets the fan function during heater tests. This menu is for Powis Parker Technicians only.

SHOW HEATER SETS

This menu displays the thermostat values for the three heaters. The first value is for the Spine Heater. This

value should be between 1550 and 2150 . The second value represents the Bender Heater. This value should be

between 1200 and 1700. The third value represents the Back Heater. This value should be between

1200 and 1700.

5 . 3 S e r v i c e M e n u D e s c r i p t i o n s

Содержание Fastback 8x




















































































Результаты поиска

Содержание Fastback 8x

Отзывы:

Powis Parker Fastback 8x, Руководство по обслуживанию, Страница: 33 / 83

Результаты поиска

Содержание Fastback 8x

Отзывы: