manualshive.com logo in svg

Powis Parker Fastback 8x, Руководство по обслуживанию, Страница: 27 / 83

Поделиться
Скачать
Powis Parker Fastback 8x Скачать руководство пользователя страница 27

 FB8X Service Manual Rev. C, 9/28/10                                                                                                                  Page 23   

S E R V I C E   M E N U

5

5 . 1   A c c e s s i n g   t h e   S e r v i c e   M e n u

 

To access the Service Menu press the OPEN and MENU buttons at the same time while      

turning the machine on.  Keep the buttons pressed until SYSTEM CHECK appears on the display.  After             
SYSTEM CHECK appears on the screen, an OK message should appear, followed by the date of the  
currently installed firmware.  After a couple seconds, AUTO-CYCLES will appear.  

5.1.1  Navigating through the Service Menu.

Use the orange OPEN and MENU buttons to toggle through the menu options.  
Use the green BIND button to select the menu option currently displayed.  

5.1.2  Warnings!

Be very careful when navigating through the Service Menu.   Altering any of the settings 
can greatly affect the performance of the machine.  

Содержание Fastback 8x




















































































Отзывы:

Нет отзывов