Powis Parker Fastback 8x Скачать руководство пользователя страница 22

Страница: 22 / 83

Page 18 FB8X Service Manual Rev. C, 9/28/10

4 . 3 M a c h i n e E r r o r s

T R O U B L E S H O O T I N G G U I D E

Possible Cause

Solution

Firmware/EEPROM mismatch.

Upgrade the firmware as shown in Section 7.

•

Error Message: MACHINE ERROR 80-82

This error indicates a problem with the EEPROM.

Possible Cause

Solution

Firmware is corrupted or the firmware transfer was
interrupted.

Perform the Flash Upgrade again with the current
firmware.

Failed Controller Assembly.

Replace the Controller Assembly.

•

Error Message: FIRMWARE ERROR

Possible Cause

Solution

Heater A_HI/A_LO values are incorrect.

Verify the A_HI/A_LO values on the heater tags match
the values in the A_HI/A_LO INPUT menu. See section
5.4.4.

Failed Controller Assembly.

If the error reoccurs after the A_HI/A_LO values have
been reentered, the Controller Assembly has failed.
Replace the Controller Assembly.

This error indicates a problem with the A_HI/A_LO values entered into the machine.

•

Error Message: MACHINE ERROR 70-75

Содержание Fastback 8x




















































































Результаты поиска

Содержание Fastback 8x

Отзывы:

Powis Parker Fastback 8x, Руководство по обслуживанию, Страница: 22 / 83

Результаты поиска

Содержание Fastback 8x

Отзывы: