Panasonic S-200PE1E8 Скачать руководство пользователя

Страница: 68 / 197

1-62

SW001

9-6-1. How to Set on PC Board

1. Turn off the power breaker to halt the supply of electricity to the PC board.
2. Open the lid of the electrical component box and confirm the location where the Select switch on the indoor

unit control PCB is placed. (Fig. 1-31)

3. Set the On/Off switches in the Off position which are now set in the On position.

Select the positions of the Select SW001 switches respectively to make the desired external static pressure
settings referring to the Table 1-7.

Table 1-7 External static pressure SW setting

External static pressure

at the time of rated

airflow volume

SW001

TP6

TP3

TP1

200

270Pa

140Pa

60Pa

250

270Pa

140Pa

72Pa

Table 1-8 Setting the external static pressure

Indoor unit

Item code

200

250

External static pressure of the rated air

flow volume

270 Pa

140 Pa

60 Pa

72 Pa

NOTE:

Failure to set this parameter may result in decreased
airflow

and condensation.

9-6-2. Operating the Timer Remote Controller

(CZ-RTC2)

How to set the external static pressure

1. Press and hold down the

and

buttons

simultaneously for 4 or more seconds.
(

, the Unit No., Item Code and Detailed Data

will blink on the LCD display.)

2. The indoor unit numbers in the group control will

be sequentially displayed whenever the Unit Select
button is pressed

Only the fan motor for the selected indoor unit will
operate during this time.

3. Specify the “

” item code by pressing the

buttons for the temperature

setting buttons and confirm the values.
(“

” set at shipment )

4. Press the

buttons for the time to amend

the values for the set data.
Refer to Table 1-8 and Fig. 1-32 and select a value
“

”, “

” or “

”.

5. Press the

button.

The display will stop blinking and remain
illuminated.

6. Press the

button. The fan motor will stop

operating and the LCD display will return to the
normal stop mode.

Indoor Unit control PC board

Fig. 1-31

CZ-RTC2

9-6-3. Operating the High-spec Wired Remote

Controller (CZ-RTC3)

How to set the external static pressure

1. Keep pressing the

and

buttons simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the
LCD display.

Maintenance func

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4.Test run

Sel.

Page [

] Confirm

20:30 (THU)

2. Press the

button to see each

menu. If you wish to see the next screen instantly,
press the

button.

Select “8. Detailed settings” on the LCD display
and press the

button.

Maintenance func

5. Sensor info.

6. Servicing check

7. Simple settings

8. Detailed settings

Sel.

Page [

] Confirm

20:30 (THU)

The “Detailed settings” screen appears on the LCD
display.
Select the “Unit no.” by pressing the

button for changes.

Detailed settings

Unit no.

Code no.

Set data

3-1

0006

Sel.

20:30 (THU)

3. Select the “Code no.” by pressing the

button.

Change the “Code no.” to “5D” by pressing the

button (or keeping it pressed).

Detailed settings

Unit no.

Code no.

Set data

Sel.

20:30 (THU)

4. Select the “Set data” by pressing the

button.

Select one of the “Set data” among “0006”, “0003”
or “0001” according to the desired external static
pressure setting by pressing the

button.
Then press the

button.

(See the table below.)
Then press the

button.

Indoor unit

External static pressure of the rated

air flow volume (Pa)

200

270 Pa
140 Pa

60 Pa

250

270 Pa
140 Pa

72 Pa

Item code

0006
0003
0001

5. Select the “Unit no.” by pressing the

button and press the

button.

The “Exit detailed settings and restart?” (Detailed
setting-end) screen appears on the LCD display.
Select “YES” and press the

button.

When the setting is completed, perform the
test run for the external static pressure setting
described in “Auto External Static Pressure Setting
Operation”.

Detailed settings

Unit no.

Code no.

Set data

1-1

0001

Sel.

20:30 (THU)

Exit detailed settings

and restart?

YES

START