Panasonic DA-DU26C Скачать руководство пользователя страница 142

Страница: 142 / 166

Problem Solving

Network Problem Solving

130

Message

Corrective Action/Additional

Information

Print/Copy Cartrdg. type mismatched

The Print/Copy Cartridge installed is
not the correct cartridge. Remove the
cartridge and check your
documentation for specifications on the
correct cartridge to install.

Printing . . .

This is a normal status message
indicating that printing is in progress.

Ready within 1 minute

This is a normal status message. The
Printer is warming up. It will be ready
for printing in a minute.

Run setup and enter correct security
key

This message is displayed if your
model requires that you enter a
security code.

Trying to connect
Please wait . . .

An error may have occurred with the
Printer. Refer to the message panel for
information.

Turn power Off
and On.

Switch Off the Printer power, wait 20
seconds, and then switch On the
power.

Warming Up . . .

This is a normal status message. The
print engine is powering up. It will be
ready for printing in a few minutes.

Содержание DA-DU26C







































































































































































Результаты поиска

Содержание DA-DU26C

Отзывы:

Похожие инструкции для DA-DU26C

Бренды по названию

Популярные бренды

Panasonic DA-DU26C, Руководство по эксплуатации

Результаты поиска

Содержание DA-DU26C

Отзывы:

Похожие инструкции для DA-DU26C

Бренды по названию

Популярные бренды