Ossila FACT1 Скачать руководство пользователя | Manualshive

Страница: 4 / 101

background image

enabling

innovative

electronics

Ossila Ltd

Copyright © 2009-2015

4

Overview

The Ossila Fast Automated Characterisation and Test (SuperFACT) system is designed to make
testing and characterisation of organic field effect transistors as simple as possible when combined
with Ossila's FET substrate systems. Fabrication of devices can be as simple as spin-coating a
material on a test-chip and loading it into the system. The automated test routines will then perform
output and/or transfer sweeps and automatically calculate the key OFET/TFT parameters for each of
the twenty devices on the substrate.

SuperFACT multiplexor makes use of a 2D array of gold-coated spring-loaded probes (POGOS) to
connects the devices to the source-meter(s), while the transistor to measure are selected through a
high performance switching network.

At the core of the measurement system is a computer controlled Keithley dual source-measure unit
with maximum output of  ±100 V and accuracy up to 10 pA.  The  Multiplexer Measurement Unit is
highly  specified  to  introduce  the  minimum  amount  of  distorsion  in  the  measurement  as  possible.
The  resistance  introduced  in  each  Drain  path  is

˂

1 Ω, leakage/noise current is

˂

500 pA and

capacitance is

˂

300 pF. This combined high level of output voltage and accuracy makes for

maximum experimental versatility and speed.

«
...
2
3
4
5
6
...
»

Содержание FACT1






































































































Отзывы:

Нет отзывов

Похожие инструкции для FACT1

Бренд: Salvis Страницы: 40

Бренд: IDEAL Страницы: 2

Бренд: Modulate Страницы: 2

Sportsound SSR-300

Бренд: Daktronics Страницы: 42

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: M-Audio Страницы: 25

Бренд: Rainbow Страницы: 35

Бренд: Rain Harvesting Страницы: 2

Бренд: Accurate Technology Страницы: 10

Бренд: Gage Bilt Страницы: 28

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

REBOUND DIABETIC WALKER

Бренд: Össur Страницы: 63

Бренд: Össur Страницы: 67

ECHODIA Babyscreen

Бренд: Électronique du Mazet Страницы: 65

Бренд: SAC Страницы: 2

accumet BASIC AB 15

Бренд: Fisher Scientific Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды