background image

www.orte.pl 

 

 

 

                                    

www.orte.pl 

                                                                                       

Page | 32 

 
 

11. WARRANTY TERMS AND CONDITIONS 

 

1.

 

The manufacturer grants a warranty on the proper operation of the Pellet Comfort boiler for 24 months from 

the date of sale. 

2.

 

Defects  revealed  during  the  24 months  from  the  date  of  purchase  will  be  removed  at  the  expense  of  the 

Manufacturer within 21 working days from the date of a written complaint sent to the Manufacturer. 

3.

 

The method, scope and conditions of repair are determined by the Manufacturer. 

4.

 

Each  defect  must  be  reported  immediately  after  discovery  and  in  writing,  using  the  attached  complaint 

protocol. This complaint protocol is also available at www.nagrzewnicenapellet.pl. 

5.

 

Documents authorizing the customer for free warranty repair are: filled Warranty Card (Installation protocol) 

and the document confirming the purchase. 

6.

 

In  case  of  the  lack  of  required  signatures,  stamps  and  dates,  the  Warranty  card  (installation  protocol)  is 

invalid. 

7.

 

A filled Installation Protocol must be sent (scan, xerox) to the Manufacturer within 14 days from the start-up 

of the machine. OTHERWISE, THE WARRANTY IS INVALID. 

8.

 

The installer (installation company) is responsible for the first commissioning and setting the parameters. 

9.

 

The warranty does not apply in the case of: 

 

installation,  commissioning  and  operation  not  in  compliance  with  the  manual  (Technical  and 

maintenance documentation) 

 

damages not resulting from the fault of the Manufacturer 

 

modifications and changes to the structure of the device 

 

too small cross-section of the chimney and to low chimney draft 

 

repairs during the warranty period made by unauthorized persons 

 

damages due to incorrect electrical installation 

 

damages due to improper transport to the boiler room 

 

improper setting of the ORTE burner 

 

burning fuel of inadequate quality (causing the production of slug and pitch deposits that are hard to 

remove) 

 

damages due to using fuel of inadequate quality or inadequate fuel 

 

no possibility of making repairs due to reasons beyond the control of the Manufacturer (e.g. no fuel, 

no access to the burner, no chimney draft etc.) 

10.

 

The warranty does not cover: 

 

adjustment of the device parameters  

 

cleaning and maintenance  

11.

 

The  costs  of  service  in  order  to  repair  complaints  due  to  the  reasons  mentioned  in  points  9  and  10  are 

covered by the customer 

12.

 

Complaints  can  be  submitted  by  post  or  e-mail  to  the  following  address:  ORTE  POLSKA  SP.  Z  O.O.,  ul. 

Groblowa 1. 05-800 Pruszków, e-mail: [email protected] 

Содержание Pellet Comfort 10








































Отзывы: