background image

www.orte.pl 

 

 

 

                                    

www.orte.pl 

                                                                                       

Page | 26 

7.5. Messages on the controller 
 
Pressing  START  button  –  the  main  switch  on  the  control  panel  –  turns  on  the  burner.  In  the  first  stage, 
lamps and the fan turn on (in order to ventilate the combustion chamber). After the chamber is ready, the 
starting  dose  of  fuel  (pellet)  is  feeder  and  the  lighter  is  turned  on.  The  feeder  needs  from  90  to  120 
seconds to ignite the fuel. 
After “identifying the flame” (when the set lightness threshold is detected by the photocell), the lighter is 
switched off and the ORTE burner goes into automatic mode. This is signalled by the message MAXIMUM 
POWER on the controller display.  
 
When the  lightness  in  the  combustion  chamber  drops  to  the  lower  value,  the  lighter  is turned on  to  re-
ignite the fuel.  
 
The state of device can be evaluated based on the displayed message. 
 

Message displayed on RK-2006LPG or 
RK-2006 SPGM 

Explanatory notes 

TEMPERATURE 67°C 
STOP 

The controller is switched off 
To resume, press START 

TEMPERATURE 67°C 
INFLAMING 

Inflaming takes place  

TEMPERATURE 67°C 
STANDBY 

STANDBY message means that the required temperature has been 
reached 

TEMPERATURE 67°C 
PUTTING OUT 

The fireplace is being put out 

TEMPERATURE 67°C 
MAXIMUM POWER 

The burner is working at maximum power in automatic mode (has 
not reached the desired temperature) 

TEMPERATURE 67°C 
MINIMUM POWER 

The burner is working at minimum power in automatic mode (has 
reached the desired temperature) 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание Pellet Comfort 10








































Отзывы: