ORTE Pellet Comfort 10 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 39

ORTE Pellet Comfort 10 Скачать руководство пользователя страница 11

www.orte.pl

www.orte.pl

Page | 11

3.6.3. Diagram of the burner

1 - fireplace inlet

4 - burner front panel

2 -  burner pipe              5 - fan cover
3 -  burner grill              6 - burner upper and back cover

3.7. Operation and storage conditions

Before installation, read the requirements of this manual and the requirements of national and local laws.
The  installation  design  should  be  performed  by  a  contractor  with  appropriate  permissions  which,  in
consultation with a chimney sweeper specialist and fire-fighting specialist, will issue a written opinion on
the  condition  of  installation  and  operation  of  the  device,  in  particular  on  the  insulation,  floor  bearing
capacity, ventilation and gas exhaust installation.
During  installation,  take  into  consideration  the  requirements  of  applicable  regulations.  In  case  of  doubt,
consult a fire protection expert.

The room where the heating device is placed must have insulation, floor bearing capacity and ventilation in
accordance with appropriate provisions, and must be connected to an individual exhaust pipe/chimney.

Storage conditions:

•

temperature between -10°C and 50°C

•

humidity between 5% and 70%

•

atmospheric pressure between 800hPa and 1200hPa

•

good ventilation – meeting the required standards (supply air at least as

extract air)
•

low dust level and lack of chemical pollution

•

room free of flammable materials

If the boiler is stored longer than 2 years from the date of manufacture, it should be started in the
premises of the manufacturer in order to verify proper operation.

«
...
9
10
11
12
13
...
»

Содержание Pellet Comfort 10








































Отзывы:

Нет отзывов