background image

www.orte.pl 

 

 

 

                                    

www.orte.pl 

                                                                                       

Page | 16 

 

Move the boiler to the place of installation. 

 

During transport, make sure not to damage the boiler. 

 

If possible, transport the boiler secured on the pallet to the place of installation. 

 

Unpack the boiler. 

 

Dispose of the packaging in accordance with environmental protection requirements. 

 
 
5.2. Installation 
 
The  Pellet  Comfort  boiler  (if  not  otherwise  requested  by  the  customer)  is  delivered,  depending  on  the 
power and the selected tray, on one or two wooden pallets. The burner is fixed to the device. The  tray is 
delivered folded. The boiler must be connected to the tray as shown in the picture. 
 
Ensure that the tray overheating sensor is inserted into a thin tube secured to the fireplace tube (stainless 
steel chimney-elbow). Connect the chimney with a flexible tube, and then connect the tube with the tray 
outlet.  
 
DANGER: Putting any objects into the tray during operation of the boiler can cause serious injuries.  
 
The tray should be covered from the top with the cover. It is forbidden to insert any objects into the tray 
during  feeder  operation,  as  this  may  cause  disability.  Remember  to  fill  up  the  tray  with  pellet  before 
operating the burner with the operating mode on the display set to “STOP”. 
After installing the feeder inside the tray and filling up with pellet, disconnect the flexible pipe from the 
burner and check the feeder usage. 

In order to determine the correct amount of the fuel quantity, use the 

following  formula:  0.2  kg  /  h  pellet  times  the  amount  of  kW  of  device  power.  E.g  .:  0.2  x  24  =  4.8.  The 
obtained result will give us in kilograms per hour (kg / h) the information we need the amount of fuel from 
obtaining  the  desired  thermal  power  in  kW.  The  burner,  when  working  in  a  given  cycle,  should  give  the 
amount of fuel for an hour that comes out of the formula. It is recommended that the feeder's working 
cycle should not exceed 75%. So if the feeder gives, for example, 25 kg in a fixed cycle, set the FUEL FOR 
MAX POWER at 19% (4.8: 25 = 0.19).

 

 
5.3. Installation conditions 
 
In  order  to  install  the  boiler,  certain  conditions  (at  the  site)  must  be  met.  The  user  and  the  installation 
company are responsible for meeting these conditions. 
The installation site must meet the following conditions: 
• Safe operation of the boiler must be ensured at the site of installation. 
• The site of installation must be protected from frost. 
• Installation and use of the boiler are allowed only in rooms with constant and proper ventilation. 
• Ensure the supply of a sufficient amount of air. 
• The floor under the boiler must have sufficient bearing capacity, and must be levelled and flat. 
• The boiler can be placed only on a non-combustible surface. 
The chimney must meet the following conditions: 
• The chimney and exhaust gas connection must comply with applicable regulations. 
• The chimney must be insensitive to moisture. 
 

 

5.4. Distance from the walls 

Содержание Pellet Comfort 10








































Отзывы: