manualshive.com logo in svg

Omron F3SG-RA, Руководство пользователя

Поделиться
Скачать
Omron F3SG-RA Скачать руководство пользователя страница 71

47

F3SG-R

User’s Manual

Chapter

2

Mu
ting

System Operation and Functions

E

2-12. Muting

Muting function temporarily disables safety function of the F3SG-RA, keeping safety output ON even if beams
are blocked. This makes it possible to install safety light curtains for AGV passage, enabling both safety and
productivity. When muting, the top-beam-state indicator (TOP), bottom-beam-state indicator (BTM) and
external indicator (if wired) connected to the auxiliary output blink to notify people in the surrounding zone that
the safety functions are disabled.
The following three operation modes are available for the muting function.
1.Standard Muting Mode (factory default setting)
2.Exit-Only Muting Mode
3.Position Detection Muting Mode

Refer to 

2-1. Combination of Functions

 for more information on the use in conjunction with other functions. 

The Muting is not available for the F3SG-RE.

The following settings are available for a beam range to be the muting state.
• All Range Disabled Setting
• Partially Disabled Setting
• Dynamic Muting Setting

The muting and override functions disable the safety functions of the device. You must ensure 
safety using other method when these functions are operating.

Install muting sensors so that they can distinguish between the object that is being allowed to be 
passed through the detection zone and a person.
If the muting function is activated by the detection of a person, it may result in serious injury.

F3SG-RA Series

X

F3SG-RE Series

Содержание F3SG-RA













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды