Omron F3SG-RA Скачать руководство пользователя страница 2

Страница: 2 / 268

Introduction

Thank you for purchasing the F3SG-



R Series Safety Light Curtain (hereinafter referred to as the "F3SG-R" ).

This is the instruction Manual describing the use of F3SG-R.

Always heed the following points when using the F3SG-R:

Be sure to have F3SG-R be handled by a "Responsible Person" who is well aware of and familiar with the machine to be installed.

The term "Responsible Person" used in this Instruction Manual means the person qualified, authorized and responsible to secure

"safety" in each process of the design, installation, operation, maintenance services and disposition of the machine.

It is assumed that F3SG-R will be used properly according to the installation environment, performance and function of the machine.

Responsible Person should conduct risk assessment on the machine and determine the suitability of this product before installation.

Read this Manual thoroughly to understand and make good use of the descriptions before installing and operating the product.

Keep this Manual at the place where the operator can refer to whenever necessary.

Original instructions

Trademarks

The Bluetooth

word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Any use of such marks by

Omron is under license. The names of the other companies and products mentioned herein are the trademarks or

registered trademarks of their respective owners.

Содержание F3SG-RA













































































































































































































































































Результаты поиска

Содержание F3SG-RA

Отзывы:

Похожие инструкции для F3SG-RA

Бренды по названию

Популярные бренды

Omron F3SG-RA, Руководство пользователя

Результаты поиска

Содержание F3SG-RA

Отзывы:

Похожие инструкции для F3SG-RA

Бренды по названию

Популярные бренды