Omron DST1 Series Скачать руководство пользователя страница 83

Страница: 83 / 114

6-2 Troubleshooting

6-2-3

Safety Output Errors

Code Error

Probable

cause

Countermeasure

hex

Configuration invalid

The configuration is invalid.

Configure the DST1 correctly.

hex

Over current detected

Trouble with the connected device Replace the connected device.

hex

Short-circuit detected

Ground fault of the output signal
line

Check the wiring.

hex

Stuck-at-high detected 1) The power source (positive side)

is in contact with the output
signal line.

2) Trouble with the internal circuit

1) Check the wiring.
2) Replace the DST1.

hex

Error in the other dual

channel output

Dual channels are set and an error
occurred in the other channel.

Remove the error in the other
channel.

hex

Internal relay relevant

circuit error

Trouble with the internal circuit (MRD
only)

Replace the DST1.

hex

Relay failure

Trouble with the relay (MRD only)

Replace the relay.

hex

Dual channel violation

Wrong setting for output data

Check the program.

hex

Cross connection

detected

Short-circuit between output signal
lines.

Check the wiring.

Explicit Message for Reading the Cause of the Error

Command

Explicit

message

Read/

write

Function

Service

code

Class

Instance

Attribute

Data

size

Response

Safety Output
Cause of Error
Information
Read

Read Reads the cause

for the normal flag
(1 to 8) specified
by the instance ID
turning OFF.
(See note.)

0E hex

hex

01 to 08

hex

6E hex

0: No error
01 hex: Configuration

invalid

02 hex: Overcurrent

detected

03 hex: Short-circuit

detected

04 hex Stuck-at-high

detected

05 hex: Error in the other

dual channel output

06 hex: Internal relay

relevant circuit error

07 hex: Relay failure
08 hex: Dual channel

violation

09 hex: Cross connection

detected

Note: The instance numbers for safety outputs 0 to 7 are 1 to 8 (01 to 08 hex), respectively.

6-5

Содержание DST1 Series



















































































































Результаты поиска

Содержание DST1 Series

Отзывы:

Omron DST1 Series, Руководство по эксплуатации, Страница: 83 / 114

Результаты поиска

Содержание DST1 Series

Отзывы: