Omron DST1 Series Скачать руководство пользователя страница 82

Страница: 82 / 114

6-2 Troubleshooting

6-2-2

Test Output Errors

Code Error

Probable

cause

Countermeasure

hex

Configuration invalid

The configuration is invalid.

Configure the DST1 correctly.

hex

Overload detected

1) Ground fault or short-circuit of

an output signal line

2) Trouble with the connected

device

1) Check the wiring.
2) Replace the connected

device.

hex

Stuck-at-high detected

1) The power source (positive

side) is in contact with the
output signal line.

2) Trouble with the internal circuit

1) Check the wiring.
2) Replace the DST1.

hex

Undercurrent

detected

using muting lamp

Trouble with the connected
device

Replace the connected device.

Explicit Message for Reading the Cause of the Error

Command

Explicit

message

Read/

write

Function

Service

code

Class

Instance

Attribute

Data

size

Response

Test Output
Cause of Error
Information
Read

Read Reads the cause

for the normal flag
(1 to 4) specified
by the instance ID
turning OFF.
(See note.)

0E hex 09 hex 01 to 04

hex

76 hex

−

0 = No error
01 hex: Configuration

invalid

02 hex: Overload

detected

05 hex: Stuck-at-high

detected

06 hex: Undercurrent

detected using
muting lamp

Note: The instance numbers for test outputs 0 to 3 are 1 to 4 (01 to 04 hex), respectively.

6-4

Содержание DST1 Series



















































































































Результаты поиска

Содержание DST1 Series

Отзывы:

Omron DST1 Series, Руководство по эксплуатации, Страница: 82 / 114

Результаты поиска

Содержание DST1 Series

Отзывы: