Omron DST1 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 114

background image

1-3 Functions

1-3-4 Safety

Outputs

Item Description

Any of the following three modes can be selected according to the external input
device.

Not Used

The safety output is not used.
(External output device not connected.)

Safety

Specifies not outputting the test pulse when the output is ON.
Contact between the output signal line and the power supply
(positive) when the output is OFF and ground faults can be
detected.

Output channel
mode

Safety Pulse Test Outputs the test pulse when the output is ON. Contact

between the output signal line and the power supply, and short
circuits with other output signal lines can be detected.

The consistency between signals on two channels can be evaluated. Either of the
following settings can be selected.

Single Channel

Specifies using Single Channel Mode. When

Single Channel

is set, the safety output that would be paired for the dual
channel parameter is also set to Single Channel Mode.

Dual channel
mode

Dual Channel

Specifies using Dual Channel Mode. When both of the safety
outputs to be paired are normal, the outputs can be turned
ON.

Output error latch
time

The OFF status is held for at least the output error latch time (0 to 65,530 ms, in
increments of 10 ms) when the individual safety output status turns OFF.

Short-circuit
detection

Supported.

Overcurrent
detection

Supported.

1-10

«
...
31
32
33
34
35
...
»

Содержание DST1 Series



















































































































Отзывы:

Нет отзывов

Похожие инструкции для DST1 Series

Бренд: Harrington Страницы: 8

MaestroKitchen 100

Бренд: Harman Kardon Страницы: 36

Бренд: ICP DAS USA Страницы: 5

Бренд: ICP DAS USA Страницы: 7

Бренд: National Instruments Страницы: 9

FieldPoint FP-AI-100

Бренд: National Instruments Страницы: 17

Бренд: Akura Страницы: 11

Бренд: Dhollandia Страницы: 82

Бренд: LSP inc. Страницы: 6

DuplicAir Intelligent Control Blue

Бренд: Jydepejsen Страницы: 52

Бренд: WAGO Страницы: 20

Бренд: Kenco Страницы: 15

Бренд: DAAB Страницы: 24

Бренд: Bouyer Страницы: 4

Бренд: Redback Страницы: 16

Бренд: BACKSAFE Страницы: 27

Бренд: Acces Страницы: 18

Бренд: vistaCNC Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды