Omron DST1 Series Скачать руководство пользователя страница 52

Страница: 52 / 114

3-2

Remote I/O Allocations

3-1-2 Safety Input Parameters

Parameter name

Value

Description

Default

S Off On Delay

0 to 126 ms
(in increments of
6 ms)

Sets the OFF/ON delay time.

0 ms

S Off On Delay

0 to 126 ms
(in increments of
6 ms)

Sets the ON/OFF delay time.

0 ms

Not Used

The safety input is not used.
(External input device not connected.)

Test Pulse from
Test Output

Specifies connecting a device with a
contact output in combination with a test
output. When this mode is selected, select
the test output to use for the test source
and then set the test output mode to

Pulse

Test Output

. When these settings are

made, contact between the input signal
line and the power supply (plus) and short
circuits with other input signal lines can be
detected.

Used as Safety
Input

Specifies connecting a safety device with

a semiconductor output, such as a light

curtain.

S Safety

Input

Channel

Mode

Used as Standard
Input

Specifies connecting a standard device

(i.e., a non-safety device).

Not Used

Not used
Test Output 0
Test Output 1
Test Output 2

S Safety

Input

Test

Source

Test Output 3

If the channel mode of a safety input is set
to

Test Pulse from Test Out

, the test

output is selected for use in combination
with the safety input. Set the channel
mode of the test output selected here to

Pulse Test Output

Not Used

Single Channel

Specifies using Single Channel Mode. If

Single Channel

is selected, the safety

input that would be paired for the dual
channel parameter will also be set to
Single Channel Mode.

Dual Channel
Equivalent

Specifies using the Dual Channel
Equivalent Mode with a paired safety
input.

S Dual

Channel

Safety

Input Mode

Dual Channel
Complementary

Specifies using Dual Channel
Complementary Mode with a paired safety
input.

Dual
Channel
Equivalent

S Dual

Channel

Safety

Input Discrepancy
Time

0 to 65,530 ms
(in increments of
10 ms)

Sets the time to monitor the logic
discrepancy in the dual channel input
logic.

0ms

I/O Comment

32 characters
max.

Sets an I/O comment for the safety input.
The I/O comment set here is used as the
I/O tag in the Logic Editor.

None

Time

Maintenance
Counter Mode
Choice

Count

Sets the operating mode for the
maintenance counter.

Time

Threshold
Maintenance
Counter

0 to
4,294,967,295
hours

Sets the threshold value for the
maintenance counter

IMPORTANT

When the Safety Input Channel Mode is set to

Test Pulse from Test Out

specify the test output to use for the test source and set the Test Output

Channel Mode of the test output to

Pulse Test Output

3-3

Содержание DST1 Series



















































































































Результаты поиска

Содержание DST1 Series

Отзывы:

Omron DST1 Series, Руководство по эксплуатации, Страница: 52 / 114

Результаты поиска

Содержание DST1 Series

Отзывы: