manualshive.com logo in svg

Omron DST1 Series, Руководство по эксплуатации, Страница: 80 / 114

Поделиться
Скачать
Omron DST1 Series Скачать руководство пользователя страница 80

6-1 Indicators and Error Processing 

 

6-1 

Indicators and Error Processing 

MS NS 

LOCK  I/O PWR I/O 

Green Red  Green Red  Yellow  Green  Yellow Red

Description 

Probable cause and remedy 

 

 

 

 

 

 

 

 

 

 

 

 

- 

- 

- 

Safety I/O communications 
in progress (normal status)

 

 

 

 

 

 

 

 

 

 

 

 

 

- - - 

Standard 

I/O 

communications or 
message communications 
in progress (normal status)

 

 

 

 

 

 

 

 

 

 

 

 

 

- 

- 

- 

The DST1 performing 
initialization process or 
waiting for configuration. 

 

 

 

 

 

 

 

 

 

- 

- 

- 

- 

Waiting for safety or 
standard connection 

 

 

 

 

 

 

 

 

 

- 

- 

- 

- 

Communications timeout 

Check the following items and 
restart the DST1. 
Are lengths of cables (trunk and 
branch lines) correct? 
Are cables broken or loose? 
Are Terminating Resistors 
connected to both ends of the trunk 
line only? 
Is noise interference excessive? 

BusOff status 
(communications stopped 
due to consecutive data 
errors) 

Check the following items and 
restart the DST1. 
Are lengths of cables (trunk and 
branch lines) correct? 
Are cables broken or loose? 
Are Terminating Resistors 
connected to both ends of the trunk 
line only? 
Is noise interference excessive? 

 

 

 

 

 

 

 

 

 

- - - - 

Node address duplication 

Reset the DST1 so that it has a 
unique node address, and then 
restart the DST1. 

 

 

 

 

 

 

 

 

- 

- 

- 

- 

Waiting for completion of 
node address duplication 
check at the master 

Reset the DST1 so that it has a 
unique node address, and then 
restart the DST1. 

 

 

 

 

 

 

 

 

 

 

- - - - 

Switch 

settings 

are 

incorrect 

Check the node address, and then 
restart the DST1. 

 

 

 

 

 

 

 

 

 

 - 

 

 

 

System failure 

Replace the DST1. 

- - - - - 

 

 

 

 

 

Input/output power is not 
supplied. 

Check the following items. 
Are cables broken? 
Is the power voltage within 
specifications? 

- - - - - 

 

 

 

 

 

An error occurred in an 
input/ output circuit. 

Check the following items. 
Has a ground fault occurred in the 
signal line? 
Is the signal line broken? 
Are there any troubles with the 
connected device? 
Is the power source (positive side) 
in contact with the signal line? 
Has a short-circuit occurred in the 
signal line? 

- - - - - 

 

 

 

 

 

When dual channels are 
set: An error occurred in 
the other channel. 

 

 : Lit   

 

 : Flashing   

 

  : Not lit 

 

6-2 

Содержание DST1 Series



















































































































Отзывы:

Нет отзывов