Omron DST1 Series Скачать руководство пользователя страница 32

Страница: 32 / 114

1-3 Functions

1-3-3 Test

Outputs

Item Description

Any of the following five modes can be selected according to the external input
device.

Not Used

The corresponding test output is not used.

Standard Output Specifies connecting to the input for a muting lamp or PLC.

Used as a monitor output.

Pulse Test
Output

Specifies connecting a device with a contact output in
combination with the safety input.

Power Supply
Output

Specifies connecting to the power supply terminal of a safety
sensor. The voltage supplied from the test output to the I/O
power supply (V, G) is output.

Test output mode

Muting Lamp
Output
(terminal T3
only)

Specifies a muting lamp output.
When the output is ON, disconnection of the muting lamp can be
detected.

Output status after
communications
error

Sets the output state of the test output when a communications error occurs.
This parameter is enabled when the Test Output Channel Mode is set to

Standard

Output

Muting Lamp Output

Short-circuit
detection

Supported.

Broken wire
detection of
external indicator

Supported.
This setting is valid when Test Output Mode is set to

Muting Lamp Output

1-9

Содержание DST1 Series



















































































































Результаты поиска

Содержание DST1 Series

Отзывы:

Omron DST1 Series, Руководство по эксплуатации, Страница: 32 / 114

Результаты поиска

Содержание DST1 Series

Отзывы: