Omron DST1 Series Скачать руководство пользователя страница 55

Страница: 55 / 114

3-2

Remote I/O Allocations

3-2

Remote I/O Allocations

3-2-1 I/O

Allocations

The DST1-series Safety I/O Terminals internally store I/O data. Connection paths can
be set using the Network Configurator to allocate I/O data for the Master Unit. Be sure
to set the required connection paths.

3-2-2 I/O

Data

The DST1-series Safety I/O Terminals store the following data.

•

SAFE

: The Controller can use this information in safety-related functions.

•

NON-SAFE

: Additional information that must not be relied on for safety functions.

Data

Description

Safety Input Data

SAFE

Indicates the ON/OFF status of each input terminal.

•

ON: 1

•

OFF: 0

Combined Safety Input
Status

SAFE

An AND of the status of all input terminals.

•

All terminals are normal: 1

•

An error has been detected in one or more input terminals: 0

Individual Safety Input
Status

SAFE

Indicates the status of each input terminal.

•

Normal: 1

•

Error: 0

Combined Safety
Output Status

SAFE

An AND of the status of all output terminals.

•

All terminals are normal: 1

•

An error has been detected in one or more output terminals: 0

Individual Safety Output
Status

SAFE

Indicates the status of each output terminal.

•

Normal: 1

•

Error: 0

Muting Lamp Status

SAFE

Indicates the status when terminal T3 is configured as the muting
lamp output.

•

Normal: 1

•

Error: 0

Safety Output Monitor

NON-SAFE

Monitors the outputs of the safety output terminals.

•

ON: 1

•

OFF: 0

Individual Test Output
Status

NON-SAFE

Indicates the status of each of the test output terminals.

•

Normal: 1

•

Error: 0

Bit 0

Safety Input Power Status Flag
0: Input power supply ON
1: Input power supply OFF

Bit 1

Safety Output Power Status Flag
0: Output power supply ON
1: Output power supply OFF

Bit 2

Network Power Voltage Drop Flag
0: Normal (higher than set monitor value)
1: Error (same as or lower than set monitor value)

Bit 3

Unit Maintenance Flag
0: Within range (lower than set monitor value)
1: Over range (same as or higher than set monitor
value)

Bit 4

Reserved

Input data

General Status Data

NON-SAFE

Bit 5

Combined I/O Port Status Flag
0: Normal (all I/O points normal)
1: Error (one or more I/O point error)

3-6

Содержание DST1 Series



















































































































Результаты поиска

Содержание DST1 Series

Отзывы:

Omron DST1 Series, Руководство по эксплуатации, Страница: 55 / 114

Результаты поиска

Содержание DST1 Series

Отзывы: